![]() ![]() The real power (watts) they can supply will depend on the power factor of your load: Watts=VA×PF, where PF is always <1.īelow you will find a theory for designing a power inverter, as well as electronic schematic diagrams for hobbyists, students and engineers. Note that commercial inverters are usually rated in volt-amps (VA). Instead they include jumper cables that can be hooked up to battery terminals. That's why the models above 200 VA usually don't even provide a plug for DC outlet. If you need to feed electronics that consumes more than that, your device has to be connected directly to the car battery. In general, the maximum power you can draw from a cigarette lighter receptacle is 12V×(fuse amperage)×η volt-amps, where η is efficiency of the inverter (typically η=0.95-0.98). This is usually enough to run your laptop or other portable electronics. ![]() Note, however, that the cigarette lighters are protected by a fuse rated typically between 10 and 20 A. Automotive inverters often come with a jack that can be plugged into a cigarette lighter. Nowadays, an inverter does not have any moving parts and unlike a generator, does not burn fuel and does not emit toxic fumes. By the way, in the past, the inversion was accomplished using alternators driven by DC motors. Although such approach is more expensive, it is usually employed in grid-tie devices, which require high quality of power. The "chopped" voltage then passes through a low-pass LC-filter to supply a clean sinusoidal output. Sine wave circuits operate in pulse width-modulated (PWM) mode, in which the generated voltage and frequency are regulated by varying the duty cycle of the high frequency pulses. In the designs with square-wave operation, output level has to be controlled on the DC side. There are also transformerless inverters, which are gaining popularity in solar systems. If an LF transformer is used, the sinusoid is generated on its primary side and transformed to the secondary side. Input to output galvanic isolation is provided by either a high-frequency transformer in the switching pre-regulator, or by a large low-frequency (LF) output transformer. Note that with a half-bridge, the DC-link voltage should be more than twice the peak of the generated output. This stage usually uses a full-bridge (see diagram to the right) or half-bridge configuration. With such a technique, first a switching pre-regulator raises a voltage from the input source to a regulated DC level corresponding to the peak value of the desired sinusoidal voltage. Most commercially manufactured models use a multi-stage concept. The described circuit is an example of a single-stage design. If such a converter uses an external excitation without current-mode control, its transformer may suffer from flux imbalance that can lead to power transistors failure. Cheap circuits suitable primarily for hobbyists projects may have just a push-pull converter with a step-up transformer. There is a number of topologies utilized in the power inverter circuits. This typs is also used in grid-connected applications. It is the most expensive type of AC source, which is used when there is a need for a sinusoidal output for certain devices, such as medical equipment, laser printers, stereos, etc. Periodically connecting the output to a specific voltage level with proper timing can produce a multiple-level waveform which is closer to sinusoidal than conventional modified one.Ī true sinewave inverter produces output with the lowest total harmonic distortion (normally below 3%). ![]() By adding two more voltage levels, a designer can reduce THD from 24% to typically 6.5%. We saw that output waveform in conventional modified sinewave DC-AC circuits has only three levels: zero or peak voltage of both polarities. If you see a device whose description does not state that it is a pure sinusoidal type, then most likely it is a square wave or a modified one. Unfortunately, the type of AC output is rarely mentioned in consumer-grade products. Nevertheless, some equipment require cleaner power. The reason most electronic devices do not care about the supplied waveform is they have an internal SMPS, which rectifies input voltage anyway. They are the most popular low-cost inverters on the consumer market today, particularly among car inverters. The models that employ such a technique are priced in the range of $.05-$0.10 per watt.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |